Customer Reviews
Good quality for the price.
After watching a couple videos on DIY for an awning replacement. I purchased this product. Very nice fit and with a little home work it was actually easy to install
It's awning fabric. Seems to be very durable, fit as expected. Replaced the fabric on my power Dometic awning. The anchor straps are nice too! Just a warning if you have a Dometic power awning. My awning tube has a spring inside it at the opposite end from the electric motor. Apparently you can pin it in place with a small screwdriver before un bolting from the arms. I was not aware of this, luckily was not hurt when it unwound. Had to re set the spring tension. It wasn't terribly difficult, but I found very limited info about this online. Guessed it at 6 wraps and it seems to be working well.
I was impressed how it was folded and packed and easy to unfold and prep for installation. It was very close to a perfect fit. Instructions were included as well. I notched the end cap on take up roller like it is on new campers now and was able to remove old one and install new one without dismantling take-up roller. BTW it is easier to remove old one if to cut it into sections.
People who bought this product also bought
-
【ULTRA-DURABLE 18OZ VINYL】 Upgraded from 15oz to 18oz heavy-duty vinyl, this camper awning replacement fabric is designed for higher durability and service life. The tensile strength test shows an average of 422 lbf and the tearing strength is 56 PSI, making it resistant to tearing and tensile force.
-
【HEAVYDUTY & NEAT DESIGN】 This 18oz RV awning fabric replacement has a 3-layer design: anti-UV composition, 18oz vinyl fabric and waterproof membrane. It is UPF50+ and 100% waterproof, protecting your eyes and skin from the harm of UV and rain. The hot-pressing process fuses both side edgings completely, ensuring a stable and neat finish without fringes or burrs.
-
【READY-TO-INSTALL】Each kit includes 3 poly-cords sewn in for easy installation, RV awning tie down kits for reducing vibration in strong wind, 7.8ft RV awning pull strap for easier rolling awning out and retracting, and 7pcs S-shaped awning hooks for holding decorations and daily necessities.
-
【TAILORED TO YOUR NEEDS!】 RV replacement fabric is available for most awning brands without metal covers, such as Dometic (A&E), Carefree, Lippert, Fiamma, Solera, Carter and Faulkner etc. Please measure the distance between the center of the right and left arms to select the correct size fabric replacement (fabric size should be less than the distance) Eg: If the length is 10', choose the size 10'(fabric 9'2”).
-
【BEST CHOICE & WARRANTY】 Neutral white topside and underside blend with outdoor surroundings. Package Included: 1* fabric replacement, 1* awning anchor kit set, 1* pull strap, 7* awning hooks, 1* repair patch, 1* user manual. We stand behind our products and provide our customers with a 24-month warranty! If you have any questions, please feel free to contact us.
Shipping Locations
RVMasking provides free delivery service only in the United States. Not available for sale outside the United States.
Shipping Fees
If your location belongs to remote areas, the resulting remote costs borne by the buyer. (Customer service specialists will contact before shipping)
We only support PayPal and Credit Card payment (Visa, Mastercard, Discover, etc). All our products are shipped free of charge, so the user only has to bear the cost of the product and no extra charges will be incurred.
Shipping Carrier
FedEx、USPS、UPS、Amazon Logistics
Processing and Delivery Time
- Processing Time: Usually 1-2 Business Days. (Except holidays)
- Shipping Time: Usually 2-5 Business Days. (Ships from our overseas warehouse in the USA)
Orders during Saturday and Sunday will be processed as quickly as possible on Monday. It may take longer process to process and deliver your orde during peak seasons. We sincerely appreciate your understading and patience.
Affected by Covid-19, the arrival time will be delayed(If you do not receive the goods for more than 15 days, please contact us by email at Support@rv-masking.com in time, we will compensate according to the product logistics)
Track Your Orders
When your order is dispatched we'll send you an email with your tracking details so you can follow its journey. If for any reason you don't receive this, please email us at Support@rv-masking.com and we'll update you on your order's progress.
Contact Us Any Time
You are welcome to email us at Support@rv-masking.com any time if you need any help with your order.
① RV Cover Installation Guide
Step 1: Put the tire cover on first. Slide the cover over the tire, took the bungee to one side, toss around the back of the tire and connect it to the other side.
Step 2: Find a nice large area to spread the cover, unfold it. Find the front and back of the cover. (The side with sewn "front" tag, that's the front)
Step 3: Flip the cover and make sure the top is facing upward. Fold over one side of the top, the other side of the top, from the bottom loosely roll up the cover toward the front.
Step 4: Take the cover to the top and put it on.(Tips: remember to make your roof clean with no twigs branches)
Step 5: Put the gutter cover on and drop one side of the cover, over the front and back. The other side is the same. Make sure all folds are out and equally space side to side.
Step 6: Put all the staps tight (including triangle straps, medium traps, and large straps)
You are so welcome to email us at Support@rv-masking.com if any help is needed.
② Boat Cover Installation Guide
Place cover over the front portion of your boat. Then pull cover slowly over the vehicle until it covers the boat. (Remember: Avoid any sharp corners as you install the cover. You may wish to pad sharp angles or tape them over with a piece of material before covering.)
Trailering With Your RVMasking Cover
- Place the long black strap through the belt sheath sewn on the cover back. Attach the strap ends into the special non-corrosive buckle. You can adjust the length of the strap using the buckle.
- Then secure the elastic cord under the middle belly of the boat or pwc.
- Then cinch up all straps tightly, so as to keep the wind from tearing the cover off when you drive. (Warning: When transporting, cover must be fastened in such a way as to eliminate "Wind Flap". Improper installation or failure to tighten the belts & straps, may cause the cover to tear.)
STRAPS: Buckles that face down will tie to each other going under. to opposite side. The buckles that face up will tie over the cover to opposite sides. The straps will wrap the entire boat going under the hull and over the boat cover refund meeting at the rub rails to connect to the buckles.
Cleaning Your Cover
Any cover will slowly collect dust on its underside, picked up from contact with the surface of the vehicle. Do not use machines with agitators - this can damage the cover and actually cause rips or tears. Do not wash in hot water! DO NOT put the cover in an automatic dryer (the fabric can melt). DO NOT dry clean. Another way to clean the dust from either the inside or outside of the cover is to put it on the vehicle and hose it off. To clean the inside, put the cover on the vehicle inside out(this can only be done if you do not have an external antenna). After rinsing off the cover, leave it on the vehicle to dry. Then fold it and return it to the trunk or usual storage place.
Installing Cover With Loops & Tie Down Straps :
Based upon the size of your boat cover, it may not be necessary to use all of the tie down straps.
- Step 1: Thread the buckle-end of the strap through the tie down loop from back to front. Pull through approximately 12 inches and tie-off with a simple overhand knot so that the strap is secure.
- Step 2: Guide the opposite end of the strap around the trailer from back to front.
- Step 3: Thread the strap through the top slot in the quick release buckle from back to front, pulling the end of the strap toward you.
- Step 4: Continue threading the strap over the center bar of the buckle and into the bottom slot of the buckle. The strap is now fully adjustable by pulling down on the loose end of webbing. Install all the straps on the cover before tightening.
- Step 5: Be sure the cover is centered on the boat, then tighten all straps securely so that the cover is taut.
- Step 6: Trim the straps. Leave approximately 12” of webbing for adjustability and trim off any excess using a pair of scissors. Lightly singe the cut edge of the webbing using a cigarette lighter to fuse the yarns and prevent the webbing from unraveling.
DO NOT SET ON FIRE AND BE SURE TO EXTINGUISH ANY FLAMES. To remove the boat cover, simply disconnect the quick release buckles by squeezing the sides. For quick and easy re-installation of the cover, leave the straps attached to the tie-down loops. After first use, check straps for tautness. If they require adjustment, untie knot and refer to step 1.
③ Car Cover Installation Guide
STEP 1: Make sure your vehicle is clear of any dust or dirt particles, so they do not get trapped in between the cover and your vehicle surface.
STEP 2: Carefully remove your RVMasking Cover from the carrying case on the top of your vehicle with the front of the cover facing the front of your vehicle, being careful it does not touch the ground. We suggest beginning towards the rear of your vehicle.
STEP 3: Slowly unroll the cover down the middle of the vehicle towards the back and cover the rear of the car making sure the edge of the cover is under the bumper.
STEP 4: Now, roll the front of the cover towards the hood of your vehicle unrolling the side as you move forward. Do the same for the other side of your vehicle.
STEP 5: Pull the front edge of the cover underneath your front bumper. Adjust the cover where needed to ensure that all areas are covered.
STEP 6: Use the strap and buckle clips, or cable lock system underneath your vehicle to secure the cover and ensure that it does not move around or get blown away. Adjust where necessary.
Customer Reviews
Good quality for the price.
After watching a couple videos on DIY for an awning replacement. I purchased this product. Very nice fit and with a little home work it was actually easy to install
It's awning fabric. Seems to be very durable, fit as expected. Replaced the fabric on my power Dometic awning. The anchor straps are nice too! Just a warning if you have a Dometic power awning. My awning tube has a spring inside it at the opposite end from the electric motor. Apparently you can pin it in place with a small screwdriver before un bolting from the arms. I was not aware of this, luckily was not hurt when it unwound. Had to re set the spring tension. It wasn't terribly difficult, but I found very limited info about this online. Guessed it at 6 wraps and it seems to be working well.
I was impressed how it was folded and packed and easy to unfold and prep for installation. It was very close to a perfect fit. Instructions were included as well. I notched the end cap on take up roller like it is on new campers now and was able to remove old one and install new one without dismantling take-up roller. BTW it is easier to remove old one if to cut it into sections.